Equipment

Expand your AirTrack training set up with additional add-ons. At 4 inches thick and 3 feet wide, the AirTrack 3 pairs perfectly with Home AirTracks 10~20, and allows for double the height for over-stretching, new drills, and creative setups. Sma…

Now for something different! The soft and bouncy AirSpots motivate kids to move and jump freely! Coordination, balance, and play all in a new way. These stacked mats also work great as spotting platforms. The AirSpot is a round version of our...

It may look like a simple undertaking, but the Air Spot can be more challenging than it looks. Determine your best plan of action to make your way from one to the other without needing a spotter. Each step could challenge you with quick feet, regaini…

Swing, step, or jump from one Air Piston to the next without going down! This obstacle is a unique one to challenge any athletes skills. Price is for a single air piston.   Make Fitness Fun! Looking for a new way to challenge the ninjas in …

Jump from the Air Hanging Door to the next by using the foot ledge at the bottom and grabbing the handles on the sides. The large circle cut out in the middle provides another way for you to grip on without falling. This obstacle is a tricky one but …

Let the 6 black arrows direct you from one side to the other. Use the straps to help you balance or try to make your way across this wobbly obstacle without falling off onto the mat below.Make Fitness Fun!Dont let your ninja course get stale, its tim…

Salmon Ladder Pads include two pads that fit the uprights of any of our Salmon Ladders or Salmon Ladder Expansions. These also help to conceal the safety system of the weight kit.

Salmon Ladder Weight Kit creates a counter resistance, by adding weight to a pulley system, which helps to keep the bar from falling with the athlete. This weight kit is only compatible with DGS Ninja Salmon Ladders.

Salmon Ladder Pegs are 10" and compatible with our Salmon Ladders. Salmon Ladder Pegs are sold individually.

The Salmon Ladder Bar is made of 1" Sch80 Aluminum that is both lightweight and durable. The two rubber ends add extra protection and helps reduce noise. The 5ft length is compatible with all DGS Ninja Salmon Ladders, but if your Salmon Ladder needs …

The Telescope Bar expands and contracts to allow for moves that would be much more difficult (or impossible) with just a normal bar. It is constructed out of aluminum and is 1.25" in diameter. This obstacle is 40" long when in the closed position and…

The T-Ledge is another way Monstro Holds is testing the finger strength of ninjas across the world! With a double-sided, 6 inch, 1.5 in deep ledge, the T-Ledge adds a whole new level of difficulty to your routine. With a 3/8 eye bolt to hang it from.…

Swap out the cliffhangers on the X-Drop with 1" Sch40 steel bar attachments. Available in black only. Includes (2) bar attachments and hardware.

The Obstacle Weight Kit includes (1) Screw Mount, (1) Button Head Hex Drive Screw, (2) Extra Thick Fender Washers, and (1) Nut. Install on the Mega Throwback or Mallet to increase the obstacle's weight, which can help to adjust the reset positio…

The Ground Plate is required for use of the Ascending Steps. These 5' wooden Ground Plates velcro to carpet bonded flooring. The bases of the Ascending Steps are designed to bolt into T-Nuts on the Ground Plate which allow for 6" increments of horizo…

See your way to the top with the BarnBuilt Eye Glass! This obstacle is constructed out of lightweight aluminum and features 12" rings and a 30" long middle pipe. The Eye Glass is available un-painted. Pair with the Floating Skyhook to creat…

Use hitch pins to mount The Spine modules! It includes an easy-swivel, big-grip handle, and high-tension hairpin cotter. The pin is 4" in length and crafted from 1038 and 4140 steel with a yellow zinc finish. 

Compatible:ST-UJB-12 Corner JunctionPack of 4 Bolt Size: M12 x 25mm

The Aluminum Truss Coupler provides a secure connection between truss segments, ensuring stability and safety in the overall truss structure.